User Tools
tech:unix:solaris:start
Differences
This shows you the differences between two versions of the page.
| Next revision | Previous revision | ||
|
tech:unix:solaris:start [2018/11/25 16:13] rk4n3 created |
tech:unix:solaris:start [2019/10/20 18:09] (current) rk4n3 |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| <typo fs:xx-large; fw:bold>Solaris Topics</typo> | <typo fs:xx-large; fw:bold>Solaris Topics</typo> | ||
| + | |||
| + | [[https://docs.oracle.com/cd/E22985_01|Oracle SPARC T4 page]] \\ | ||
| + | {{tech:unix:solaris:e22992.pdf|SPARC T4 Getting Started Guide (PDF)}} \\ | ||
| + | {{tech:unix:solaris:e22988.pdf|SPARC T4 Server Installation Guide (PDF)}} \\ | ||
| + | |||
| + | ====== Installation & Configuration ====== | ||
| + | ==== Serial Console ==== | ||
| + | * Use the ''minicom -D /dev/devicename'' command from Linux //(''/dev/ttyUSB0'')// | ||
| + | * Serial configuration: ''9600 8-N-1'' | ||
| + | * At the ''->'' prompt, ''start /SYS'' starts ILOM, ''start /HOST/console'' starts pre-boot console | ||
| + | * At the ''{0} ok'' prompt, typically the ''boot'' command should work | ||
| + | * Use ''probe-scsi-all'' to list all disk info | ||
| + | * The ''printenv boot-device'' command shows current boot setting | ||
| + | * May have to use the ''setenv boot-device newbootdevspec'' command to change boot device | ||
| + | |||
| + | ==== DNS (client) ==== | ||
| + | |||
| + | Prepare a list of domains to search and the IP addresses of the DNS name servers on your network. | ||
| + | Set properties in the SMF repository with the information:<code> | ||
| + | $ svccfg -s network/dns/client | ||
| + | svc:/network/dns/client> setprop config/search = astring: ("domain1" "domain2") | ||
| + | svc:/network/dns/client> setprop config/nameserver = net_address: (address1 address2) | ||
| + | svc:/network/dns/client> select network/dns/client:default | ||
| + | svc:/network/dns/client:default> refresh | ||
| + | svc:/network/dns/client:default> validate</code> | ||
| + | Specify the name service switch to use DNS:<code> | ||
| + | svc:/network/dns/client:default> select name-service/switch | ||
| + | svc:/system/name-service/switch> setprop config/host = astring: "files dns" | ||
| + | svc:/system/name-service/switch> select system/name-service/switch:default | ||
| + | svc:/system/name-service/switch:default> refresh | ||
| + | svc:/system/name-service/switch:default> validate | ||
| + | svc:/system/name-service/switch:default> quit</code> | ||
| + | Start the services that are needed to run the DNS client:<code> | ||
| + | $ svcadm enable dns/client | ||
| + | $ svcadm enable name-service/switch</code> | ||
| ====== Trivia ====== | ====== Trivia ====== | ||
| Line 7: | Line 42: | ||
| svcadm restart system/identity:node</code> | svcadm restart system/identity:node</code> | ||
| + | |||
| + | ==== Sample output ... ==== | ||
| + | <WRAP prewrap><code> | ||
| + | {0} ok probe-scsi-all | ||
| + | /pci@400/pci@2/pci@0/pci@f/pci@0/usb@0,2/hub@2/hub@3/storage@2 | ||
| + | Unit 0 Removable Read Only device AMI Virtual CDROM 1.00 | ||
| + | |||
| + | /pci@400/pci@2/pci@0/pci@4/scsi@0 | ||
| + | |||
| + | FCode Version 1.00.64, MPT Version 2.00, Firmware Version 9.00.00.00 | ||
| + | |||
| + | Target 9 | ||
| + | Unit 0 Disk HITACHI H103030SCSUN300G A2A8 585937500 Blocks, 300 GB | ||
| + | SASDeviceName 5000cca00a83c874 SASAddress 5000cca00a83c875 PhyNum 2 | ||
| + | Target a | ||
| + | Unit 0 Removable Read Only device TEAC DV-W28SS-V 1.0B | ||
| + | SATA device PhyNum 6 | ||
| + | Target b | ||
| + | Unit 0 Disk ATA ST9500620NS SN01 976773168 Blocks, 500 GB | ||
| + | SATAWorldWideName 5000c5002e5a1b90 PhyNum 3 | ||
| + | |||
| + | /pci@400/pci@1/pci@0/pci@4/scsi@0 | ||
| + | |||
| + | FCode Version 1.00.64, MPT Version 2.00, Firmware Version 9.00.00.00 | ||
| + | </code></WRAP> | ||
tech/unix/solaris/start.1543184017.txt.gz ยท Last modified: 2018/11/25 16:13 by rk4n3
Page Tools
