User Tools
tech:linux:start
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
tech:linux:start [2020/05/01 00:41] rk4n3 |
tech:linux:start [2022/11/13 23:20] (current) rk4n3 |
||
|---|---|---|---|
| Line 16: | Line 16: | ||
| <code>qemu-img create -f qcow2 sda 18G</code> | <code>qemu-img create -f qcow2 sda 18G</code> | ||
| <code>lvcreate -L 100G -n vmnamehome vgvms</code> | <code>lvcreate -L 100G -n vmnamehome vgvms</code> | ||
| + | |||
| + | See [[:tech:virt:start|here]] for further details | ||
| + | |||
| ===== Misc Tech Trivia ===== | ===== Misc Tech Trivia ===== | ||
| + | |||
| + | ==== X11 Display Auth ==== | ||
| + | * From display owner //(where X is display number)//: ''xauth extract cookiefilename ://**X**//'' | ||
| + | * For remote user, get cookie file and: ''xauth merge cookiefilename'' | ||
| + | |||
| ==== Storage Management ==== | ==== Storage Management ==== | ||
| - | * Set up RAID5 with `mdadm`:<code> | + | * Good article: [[https://www.digitalocean.com/community/tutorials/how-to-create-raid-arrays-with-mdadm-on-ubuntu-18-04]] |
| - | mdadm --create --verbose /dev/md0 --level=5 --raid-devices=3 /dev/sdX /dev/sdY /dev/sdZ | + | * **NOTE:** There seems to be issues with some hardware, where GPT partition tables are manipulated by some UEFI functionality, and so RAID volumes created on raw disk (without partition) are at risk of losing their superblock(s). Because of this, its generally recommended to utilize a partition instead of full-disk devices. |
| - | cat /proc/mdstat | + | * Set up RAID5 with ''mdadm'':<code>mdadm --create --verbose /dev/md0 --level=5 --raid-devices=3 /dev/sdX1 /dev/sdY1 /dev/sdZ1</code> |
| + | * Check status: ''cat /proc/mdstat'' | ||
| + | * Configure for availability after boot: \\ //(**NOTE**: this must be done after recovery status is complete)//<code> | ||
| mdadm --detail --scan >> /etc/mdadm/mdadm.conf | mdadm --detail --scan >> /etc/mdadm/mdadm.conf | ||
| update-initramfs -u | update-initramfs -u | ||
| </code> | </code> | ||
| - | * Sample LVM with `mdadm` RAID:<code> | + | * Scrub to prevent bit-rot: ''echo check > /sys/block/md**X**1/md/sync_action'' \\ (use ''cat /proc/mdstat'' to monitor) |
| + | * Tune re-build speed ([[https://www.cyberciti.biz/tips/linux-raid-increase-resync-rebuild-speed.html]]): \\ To show limits: ''sysctl dev.raid.speed_limit_min ; sysctl dev.raid.speed_limit_max'' \\ To increase speed, enter: ''sysctl -w dev.raid.speed_limit_min=value'' \\ In ''/etc/sysctl.conf''<code>dev.raid.speed_limit_min = 50000 | ||
| + | ## good for 4-5 disks based array ## | ||
| + | dev.raid.speed_limit_max = 2000000 | ||
| + | ## good for large 6-12 disks based array ### | ||
| + | dev.raid.speed_limit_max = 5000000</code> | ||
| + | * Sample LVM with ''mdadm'' RAID:<code> | ||
| pvcreate -M2 /dev/md0 | pvcreate -M2 /dev/md0 | ||
| vgcreate -s 64 newvg /dev/md0 | vgcreate -s 64 newvg /dev/md0 | ||
tech/linux/start.1588311687.txt.gz · Last modified: 2020/05/01 00:41 by rk4n3
Page Tools
